Attention: Metallographic Inspection Control Indicators for Fixed Jaw Plates
You are here: Home » Blogs » Industry Blogs » Attention: Metallographic Inspection Control Indicators for Fixed Jaw Plates

Attention: Metallographic Inspection Control Indicators for Fixed Jaw Plates

Views: 0     Author: Hunan Xiangjian Machinery Technology Co., Ltd.     Publish Time: 2026-11-20      Origin: Site

Inquire

wechat sharing button
line sharing button
twitter sharing button
facebook sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Attention: Metallographic Inspection Control Indicators for Fixed Jaw Plates

As a core wear-resistant and load-bearing component of jaw crushers, fixed jaw plates are mostly made of high manganese steel. The batch performance stability directly affects on-site service life and production operation & maintenance costs. Metallographic sampling inspection is a core approach to control the internal quality of products in mass production. By observing key metallographic structure indicators, process fluctuations in casting and heat treatment links can be identified in time, batch performance deviations can be avoided, and the wear resistance and impact resistance of products in the same batch can be kept stable and consistent.

Matrix structure type and austenite uniformity are the primary control indicators. For qualified water-toughened high manganese steel fixed jaw plates, the matrix should be a uniform single-phase austenite structure. During sampling inspection, it is necessary to confirm whether there are austenite decomposition products such as pearlite and bainite in the matrix. The occurrence of such structures usually corresponds to insufficient cooling rate or deviation of heat preservation parameters, which will directly weaken the work hardening ability of the material and reduce the overall wear resistance. Meanwhile, the austenite grain size and size uniformity need to be tested. The grain size state can intuitively reflect the stability of the heat treatment process. Coarse grains or excessive differences in grain size grades in the same batch will lead to decreased matrix toughness and fluctuated impact resistance, which may cause early failure when processing hard materials such as granite.

The morphology, distribution and area proportion of carbides are core control items. The core goal of water toughening treatment is to fully dissolve alloy carbides into the austenite matrix. In qualified products, residual carbides should be in fine granular and dispersed distribution, and no continuous network carbides along grain boundaries are allowed. During sampling inspection, focus should be placed on the grain boundary state. The occurrence of network carbides usually corresponds to low initial water cooling temperature or insufficient holding time, which will split the continuity of the matrix structure, greatly reduce the impact toughness of the jaw plate, and easily cause faults such as tooth chipping and matrix fracture in on-site use. At the same time, the area proportion of carbides should be counted. If the proportion fluctuates too much between different furnace batches, it indicates unstable factors in smelting composition control or heat treatment process, and production parameters need to be adjusted in time.

The grade of non-metallic inclusions and the proportion of micro casting defects are important supplementary control indicators. Non-metallic inclusions such as oxides and sulfides remaining during smelting and casting will become natural stress concentration sources inside the material. Sampling inspection shall evaluate the inclusion grade according to corresponding industry standards, and monitor their size, quantity and distribution state. Excessive inclusion grade will significantly reduce the fatigue strength of the jaw plate and easily cause early cracking under alternating impact loads. Meanwhile, the distribution density of micro casting defects such as micro porosity and micro shrinkage cavities shall be observed. A high proportion of such defects indicates fluctuations in the casting feeding system or casting parameters, which will accelerate crack propagation and fault evolution during product service.

Through joint control of multi-dimensional metallographic indicators, the batch performance consistency of fixed jaw plates can be effectively guaranteed, making the on-site service life more predictable. Hunan Xiangjian Machinery Technology Co., Ltd. focuses on the field of mine wear-resistant parts, implements a strict metallographic sampling inspection system in the mass production of fixed jaw plates, and controls various structural indicators batch by batch to ensure that products adapt to scenarios such as ore crushing, sand making and construction waste treatment. For more details on quality control, please visit the official website www.xjgmg.com for consultation.

Hunan Xiangjian Machinery Technology Co., Ltd. is a professional mining machinery equipment and wear parts manufacturer integrating design, development, manufacturing and sales.

CONTACT INFORMATION

Phone:+86-13327312194
Email: zq@xjgmg.com
Add:Chaofeng Industrial Park, Santangpu Town, Shuangfeng County, Loudi City, Hunan Province, China

QUICK LINKS

PRODUCTS

CONTACT US
Copyright © 2024 Hunan Xiangjian Machinery Technology Co., Ltd. All rights reserved. Sitemap Support by leadong.com Privacy Policy